Melodic sounds thrill the soul, sooth the mind and comforts the spirit. But sometimes rhythmic sounds are simply there to rock listeners physically as they dance to tunes that appeal to them. This is precisely what steel pan music does. The pans go through an intricate process which enables them to produce the diverse range of sounds for which they are known. The instruments that produce these awesome sounds are produced through a very intricate process that takes a lot of physical and mental exertion.
Creating music by using the steel pans is an art that is closely associated with the Caribbean region. Calypso songs are enhanced by the accompaniment of sweet rhythmic sounds emanating from these musical tunes. Trinidad and Tobago's musicians are famed for being the pioneers in this area.
Even though the musical genre has strong ties to the Caribbean, the sounds produced are so diverse that they can be used to create the sounds of any category of musical expressions. These musical tools are found in rhythm and blues, gospel, reggae and many other types of bands. There is no genre that they cannot fit into.
The most authentic steel pans are made by hand. When making steel pans, experts first select the type of drum to use. Traditionally, they use drums that once contained oil. Drum selection is a crucial part of the process because the type of drum used determines the type of sound the resulting instrument will produce. The general rule is that the lower the pitch desired then the thicker the drum needs to be.
The drums selected must have one end opened and the bottom must remain sealed. The maker will sink the bottom to create a bowl-like appearance from the inside. During this step, if the drum selected was too thin, or rusted, or dented badly, it may burst due to the pressure being applied. It is clear therefore, why it is crucial to consider drum quality from the initial phase.
The sinking process is one of the steps that helps to make the instrument produce the desired notes. After sinking, the drum is once again adjusted to ensure that it produces the desired noted. It is marked to identify the areas that should produce each note. The unmarked areas are then flattened in with a special tuning hammer.
The pan will have to go through a few other stages before it is ready for use. It must be grooved, set, cut and tuned. It then has to be coated with a layer that not only protects the look but also the adjustments that have been made to its surface. Then it must go through a step known as fine tuning and blending.
A steel pan goes through a very detailed and intricate process before it gets to the musician. The sounds that people around the world enjoy so much are the products of, not just the musical talent using it but also the expert craftsmen who exert much effort and expertise in making it.
Creating music by using the steel pans is an art that is closely associated with the Caribbean region. Calypso songs are enhanced by the accompaniment of sweet rhythmic sounds emanating from these musical tunes. Trinidad and Tobago's musicians are famed for being the pioneers in this area.
Even though the musical genre has strong ties to the Caribbean, the sounds produced are so diverse that they can be used to create the sounds of any category of musical expressions. These musical tools are found in rhythm and blues, gospel, reggae and many other types of bands. There is no genre that they cannot fit into.
The most authentic steel pans are made by hand. When making steel pans, experts first select the type of drum to use. Traditionally, they use drums that once contained oil. Drum selection is a crucial part of the process because the type of drum used determines the type of sound the resulting instrument will produce. The general rule is that the lower the pitch desired then the thicker the drum needs to be.
The drums selected must have one end opened and the bottom must remain sealed. The maker will sink the bottom to create a bowl-like appearance from the inside. During this step, if the drum selected was too thin, or rusted, or dented badly, it may burst due to the pressure being applied. It is clear therefore, why it is crucial to consider drum quality from the initial phase.
The sinking process is one of the steps that helps to make the instrument produce the desired notes. After sinking, the drum is once again adjusted to ensure that it produces the desired noted. It is marked to identify the areas that should produce each note. The unmarked areas are then flattened in with a special tuning hammer.
The pan will have to go through a few other stages before it is ready for use. It must be grooved, set, cut and tuned. It then has to be coated with a layer that not only protects the look but also the adjustments that have been made to its surface. Then it must go through a step known as fine tuning and blending.
A steel pan goes through a very detailed and intricate process before it gets to the musician. The sounds that people around the world enjoy so much are the products of, not just the musical talent using it but also the expert craftsmen who exert much effort and expertise in making it.
About the Author:
You can visit steel-pan.com for more helpful information about The Instrument Behind Steel Pan Music.
No comments:
Post a Comment